Skip to main content

Shear centre

The Shear centre is a point where a shear force can act without producing any twist in the section. At Shear centre of a section the applied force is balanced by the set of shear forces obtained by summing the shear stresses over the section.
Shear centre is also known as the centre of twist.
When the load does not act through the shear center, in addition to bending, a twisting moment will develop  in the section. 
The location of the shear center is independent of the direction and magnitude of the transverse forces.
In unsymmetrical sections and in particular angle and channel sections, the summation of the Shear Stresses in each leg gives a set of Forces which must be in equilibrium with the applied Shearing Force.
(a) Consider the angle section which is bending about a principal axis and with a Shearing Force F at right angle to this axis. The sum of the Shear Stresses produces a force in the direction of each leg as shown above. It is clear that their resultant passes through the corner of the angle and unless F is applied through this point there will be a twisting of the angle as well as Bending. This point is known as The Shear Centre or Centre of Twist
(b) For a channel section with loading parallel to the Web, the total Shearing Force carried by the web must equal F and that in the flanges produces two equal and opposite horizontal forces. It can be seen that for equilibrium the applied load causing F must lie in a plane outside the channel as indicated. 
Note:
1. In case of a beam having two axes of symmetry, the shear centre coincides with the centroid.
2. In case of sections having one axis of symmetry, the shear centre does not coincide with the centroid but lies on the axis of symmetry.
3. When the load passes through the shear centre then there will be only bending in the cross section and no twisting.

Example:

1. A H-section with unequal flanges as shown in fig. If the smaller flange is 16mm x 100mm the larger flange is 16mm by 200mm, and the web is 9mm by 284mm. Find the location of the shear center from the center of the bigger flange.

Solution:
The shear centre lies on the axis of symmetry and at a distance of x form the center of large flange.
Taking the moments about shear center

Comments

  1. thank u sir....I got the concept...

    ReplyDelete
  2. can this concept used for unsymmetrical lipped c section ?

    ReplyDelete
  3. Sir,
    I have some conceptual problems about shear centre of angular sections.How can i contact you?i have attached the problem and just waiting for the answer of e=? with all the procedures that will clarify my doubt.my doubt is how to calculate ý at angular sections.

    With regards

    Attachments area
    Preview attachment 20151110_185806.jpg
    Image
    20151110_185806.jpg

    ReplyDelete
    Replies
    1. Dear Abisek,
      For a channel section with loading parallel to the Web, the total Shearing Force carried by the web must equal F and that in the flanges produces two equal and opposite horizontal forces. It can be seen that for equilibrium the applied load causing F must lie in a plane outside the channel. Your problem is also have shear center out side of the section. But the total shear force carried by the web and vertical projections, vertical components of inclined portion must equal to external force. The horizontal component of inclined portions will produce anti clock wise moment and that will be balanced clock wise moment produced by the force witch will act at shear center. Using this concept you can find 'e"

      Delete
    2. The flange of channel section are situated same side. How can they carry equal and opposite force.please explain..

      Delete
  4. sir i need the formula of shear center for lipped channel section

    ReplyDelete

Post a Comment

Popular posts from this blog

Relation between Modulus of Elasticity and Modulus of Rigidity

Modulus of Elasticity (E)   It is the ratio between Normal stress to Normal strain within the elastic limit. Elastic Modulus E = Normal stress/Normal strain E =  s/e Modulus of Rigidity (G)  It is the ratio between Shear stress to Shear strain within the elastic limit. Rigidity Modulus G = Shear stress/ Shear strain G =    Ƭ / ø   Relation between Modulus of Elasticity and Modulus of Rigidity: Consider a solid cube  PQRS is  subjected to a shearing force F.  Let  Ƭ     be the shear stress produced in the faces PQ and RS due to this shear force. The complementary shear stress consequently produced in the vertical faces PS and RQ is also equal to same and shown in figure as Ƭ   Due to the pure shearing force, the cube is deformed PQRS to PQR'S' . The point   S moved to S' and point R moved to R' as shown in fig.  The shear strain = The angle of distortion  ø                          ø = RR'/ RQ ---(1) Shear strain = Shear stress /Rigidity modulus                

PORTAL METHOD and CANTILEVER METHOD

The behavior of a structure subjected to horizontal forces depends on its height to width ratio. The deformation in low-rise structures, where the height is smaller than its width, is characterized predominantly by shear deformations. In high rise building, where height is several times greater than its lateral dimensions, is dominated by bending action. To analyze the structures subjected to horizontal loading we have two methods. Portal method  and Cantilever method 1. PORTAL METHOD The portal method is an approximate analysis used for analysing building frames subjected to lateral loads such as Wind loads/ seismic forces.  Since shear deformations are dominant in low rise structures, the method makes simplifying assumptions regarding horizontal shear in columns.  Each bay of a structure is treated as a portal frame, and horizontal force is distributed equally among them. Assumptions in portal method   1. The points of inflection are located at the mid-height of each column above th

Shearing Stresses Distribution in Circular Section

Show that the shearing stress developed at the neutral axis of a beam with circular cross section is  τ max = (4/3)(F/πr2). Assume that the shearing stress is uniformly distributed across the neutral axis.  Solution : Let us consider the circular section of a beam as displayed in following figure. We have assumed one layer EF at a distance y1 from the neutral axis of the circular section of the beam Shear stress at a section will be given by following formula as mentioned here Where, F = Shear force (N) τ = Shear stress (N/mm2) A = Area of section, where shear stress is to be determined (mm2) ȳ = Distance of C.G of the area, where shear stress is to be determined, from neutral axis of the beam section (m) Q = A. ȳ = Moment of the whole shaded area about the neutral axis I = Moment of inertia of the given section about the neutral axis (mm4) For circular cross-section, Moment of inertia, I = ПR4/4 b = Width of the given section where shear stress is to be determined. Let us consider on