Skip to main content

Posts

Beam Deflections - Moment - Area Method

Moment - Area Method - Mohr's  Theorems  Otto Mohr (1835-1918)  German Civil Engineer In this method, to determining the slopes and deflections in beams involves the Area and Moment of the ' Bending moment diagram' .   ( B.M.D ) First Theorem : The angle between tangents drawn at any two points on deflected curve, is equal to area of the M/EI diagram between the two points. The angle between the tangents from points A and B  O  AB =  1/EI (Area of AB) Second Theorem : The intercept on a vertical line made by two tangents drawn at the two points on the deflected curve is equal to the moment of the M/EI diagram between two points about the vertical line. The intercepts at point A,and B are, t A/B = Z AB  = 1/EI (Area of AB). X A   and t   B/A  =  Z  BA   =   1/EI (Area of AB). X B Sign Convention : For +ve B.M. ,the area of  M/EI diagram is consider...

Deflection of Beams

The deformation of a beam is usually expressed in terms of its deflection from its original unloaded position.  The deflection is measured from the original neutral surface of the beam to the neutral surface of the deformed beam. The configuration assumed by the deformed neutral surface is known as the elastic curve of the beam.  The angle through which the cross-section rotates with respect to the original position is called the angular rotation of the section.  Generalized  Deflection equation Consider a small element dx in deflected beam as shown below. In Cartesian coordinates, the radius of curvature(R) of a curve and deflection y = f(x) is have the relation given below,  The deflection is very small ,the slope of the curve dy/dx is also very small and squaring of this we may get a negligible valve and may neglect in the above equation.  1/R = d2y/dx2 In the derivation of flexure formula, the radius of curvature of a beam is given as  1/R = M /EI...

TORSION

Consider a bar to be rigidly attached at one end and twisted at the other end by a torque or twisting moment T equivalent to F × d, which is applied perpendicular to the axis of the bar, as shown in the figure. Such a bar is said to be in torsion. Assumptions in Torsional equation 1. The material of the shaft is homogeneous and isotropic throughout length of shaft. 2. The shaft is circular in cross-section remains circular even after loading.  3. A plane section of the shaft normal to its axis before loading remains plane even after the torque has been applied.  4. The twist along the length of the shaft is uniform.  5. The distance between any two normal cross-sections remains same even after application of torque.  6. The maximum shear stress induced in the shaft due to application of torque does not exceed its elastic limit value. Derivation of Torsion Formula  Hear R is the outer radius of the shaft.  t   ...

@Work Place- CIET - Lam, Guntur (2007-2014)

Short Answer questions -S.A.II

                                               1.      What is Slope Deflection Method?(Oct/Nov 2010)           The Slope Deflection  equations gives the moments at end of a member. These are expressed in terms of  the deformations (ie.slopes & displacements). This method is used for the analysis statically indeterminate beams and rigid frames.     2.      What are the assumptions used in the slope deflection method?(Oct/Nov 2010)      1) The method of the structure is linearly elastic.     2) The structure is loaded within the elastic limit of its material and the principle of superposition is also for the analysis.    3) The axial displacements and shear displacements are negligible and they are neglected in the analys...

Plastic Behaviour of structures

Most Engineering design is based on the "Elastic Theory of Bending" and the method is to calculate the maximum Stresses which occur, and to then keep them within the working Stresses in both compression and Tension. These working Stresses are calculated from the Yield (or ultimate) Stress and a Factor of Safety.  This approach is a little unrealistic since Mild Steel Structures do not fail when the edge Stress of any cross section reaches the Yield point, and will continue to withstand the load as long as the central core of the section remains within the Elastic State.  Through ductility, structure is able to absorb large deformations beyond elastic limit without the danger of fracture. It is this characteristics feature of steel that makes possible the application of plastic analysis to structural design. Figure 1: Stress strain diagram (for mild steel) Stress-strain diagram for mild steel in tension is shown in figure-1. Let ‘ab’ represent the elastic range, ...

SLOPE DEFLECTION METHOD

The slope deflection equations express the member end moments in terms of rotation angles and deflections. The slope deflection method is used for analysis of statically indeterminate structures such as beams and frames. This method was  introduced  by Prof.George A. Maney,in 1915. Sign Convention: 1. The clock wise moments,and clock wise rotations/slopes are taken as positive ones. 2. The down ward displacements of the right end with respect to the left end of horizontal  member is considered as positive. 3. The right ward displacement of upper end with respect to lower end of a vertical member is taken as positive.  Assumptions in the slope- deflection method: 1. The material of the structure is linearly elastic. 2. The structure is loaded with in elastic limit. 3. Axial displacements,Shear displacements are neglected. 4. Only flexural deformations are considered The slope deflection equations of member AB of flexural rigi...